Servus,

ich habe einen Schaltschrank, indem ich gerne die Temperatur und Luftfeuchtigkeit auslesen möchte...

Also 1x Sensor an Pin 12

Programm läuft (gut zusammen kopiert) ich habe nicht wirkich Ahnung vom Programmieren.

Aber ich bin ja kreativ und Schwabe... und da fangen meine Probleme an Ich dachte mir... ja klasse... der ESP hat ja mehrere Pins um DHT22 Sensoren zu installieren... also könnte ich noch die Außentemperatur und Raumtemperatur mit abnehmen und mir ausgeben lassen... aber so recht klappt das nicht...

Ich habe den zusätzlichen Sensor mal: DHT22PIN2 genannt... hab aber die veränderten Zeilen auskommentiert. Habe mal alle Änderungen "Fett" makiert.

Bei dem untersten Block hab ich schon mehrere Dinge ausprobiert... das kann ich nun aber nicht alles in einem Sketch wiedergeben.

Ich habs geschafft, dass er bei Node Red zwar auf Temp2 und Num2 einen Wert ausgibt... jedoch der selbe wie beim Sensor 1.

Hier mal mein Sketch:
/*
Rui Santos & Sara Santos - Random Nerd Tutorials
Complete project details at https://randomnerdtutorials.com/esp32-mqtt-publish-dht11-dht22-arduino/
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files.
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
*/
#include "DHT.h"
#include
extern "C" {
#include "freertos/FreeRTOS.h"
#include "freertos/timers.h"
}
#include
#include

#define WIFI_SSID ""
#define WIFI_PASSWORD ""

// Raspberry Pi Mosquitto MQTT Broker
#define MQTT_HOST IPAddress (192, 168, 1, 9)
// For a cloud MQTT broker, type the domain name
//#define MQTT_HOST ""
#define MQTT_PORT 1883

// Temperature MQTT Topics
#define MQTT_PUB_TEMP "esp32/dht/temperature"
#define MQTT_PUB_HUM "esp32/dht/humidity"
//#define MQTT_PUB_TEMP2 "esp32/dht/temperature2"
//#define MQTT_PUB_HUM2 "esp32/dht/humidity2"

// Digital pin connected to the DHT sensor
#define DHTPIN 12
//#define DHTPIN2 14

// Uncomment whatever DHT sensor type you're using
//#define DHTTYPE DHT11 // DHT 11
#define DHTTYPE DHT22 // DHT 22 (AM2302), AM2321
//#define DHTTYPE DHT21 // DHT 21 (AM2301)

// Initialize DHT sensor
DHT dht (DHTPIN, DHTTYPE) ;
//DHT dht2 (DHTPIN2, DHTTYPE) ;

// Variables to hold sensor readings
float temp;
float hum;
//float temp2;
//float hum2;

AsyncMqttClient mqttClient;
TimerHandle_t mqttReconnectTimer;
TimerHandle_t wifiReconnectTimer;

unsigned long previousMillis = 0; // Stores last time temperature was published
const long interval = 10000; // Interval at which to publish sensor readings

void connectToWifi () {
Serial.println ("Connecting to Wi-Fi...") ;
WiFi.begin (WIFI_SSID, WIFI_PASSWORD) ;
}

void connectToMqtt () {
Serial.println ("Connecting to MQTT...") ;
mqttClient.connect () ;
}

void WiFiEvent (WiFiEvent_t event) {
Serial.printf ("[WiFi-event] event: %d\n", event) ;
switch (event) {
case ARDUINO_EVENT_WIFI_STA_GOT_IP:
Serial.println ("WiFi connected") ;
Serial.println ("IP address: ") ;
Serial.println (WiFi.localIP () ) ;
connectToMqtt () ;
break;
case ARDUINO_EVENT_WIFI_STA_DISCONNECTED:
Serial.println ("WiFi lost connection") ;
xTimerStop (mqttReconnectTimer, 0) ; // ensure we don't reconnect to MQTT while reconnecting to Wi-Fi
xTimerStart (wifiReconnectTimer, 0) ;
break;
}
}

void onMqttConnect (bool sessionPresent) {
Serial.println ("Connected to MQTT.") ;
Serial.print ("Session present: ") ;
Serial.println (sessionPresent) ;
}

void onMqttDisconnect (AsyncMqttClientDisconnectReason reason) {
Serial.println ("Disconnected from MQTT.") ;
if (WiFi.isConnected () ) {
xTimerStart (mqttReconnectTimer, 0) ;
}
}

/*void onMqttSubscribe (uint16_t packetId, uint8_t qos) {
Serial.println ("Subscribe acknowledged.") ;
Serial.print (" packetId: ") ;
Serial.println (packetId) ;
Serial.print (" qos: ") ;
Serial.println (qos) ;
}
void onMqttUnsubscribe (uint16_t packetId) {
Serial.println ("Unsubscribe acknowledged.") ;
Serial.print (" packetId: ") ;
Serial.println (packetId) ;
}*/

void onMqttPublish (uint16_t packetId) {
Serial.print ("Publish acknowledged.") ;
Serial.print (" packetId: ") ;
Serial.println (packetId) ;
}

void setup () {
Serial.begin (115200) ;
Serial.println () ;

dht.begin () ;

mqttReconnectTimer = xTimerCreate ("mqttTimer", pdMS_TO_TICKS (2000), pdFALSE, (void*) 0, reinterpret_cast (connectToMqtt) ) ;
wifiReconnectTimer = xTimerCreate ("wifiTimer", pdMS_TO_TICKS (2000), pdFALSE, (void*) 0, reinterpret_cast (connectToWifi) ) ;

WiFi.onEvent (WiFiEvent) ;

mqttClient.onConnect (onMqttConnect) ;
mqttClient.onDisconnect (onMqttDisconnect) ;
//mqttClient.onSubscribe (onMqttSubscribe) ;
//mqttClient.onUnsubscribe (onMqttUnsubscribe) ;
mqttClient.onPublish (onMqttPublish) ;
mqttClient.setServer (MQTT_HOST, MQTT_PORT) ;
// If your broker requires authentication (username and password), set them below
//mqttClient.setCredentials ("REPlACE_WITH_YOUR_USER", "REPLACE_WITH_YOUR_PASSWORD") ;
connectToWifi () ;
ArduinoOTA.setHostname ("OTA") ;
ArduinoOTA.begin () ;
}

void loop () {
ArduinoOTA.handle () ;
unsigned long currentMillis = millis () ;
// Every X number of seconds (interval = 10 seconds)
// it publishes a new MQTT message
if (currentMillis - previousMillis >= interval) {
// Save the last time a new reading was published
previousMillis = currentMillis;
// New DHT sensor readings
hum = dht.readHumidity () ;
//hum2 = dht2.readHumidity () ;
// Read temperature as Celsius (the default)
temp = dht.readTemperature () ;
//temp2 = dht2.readTemperature () ;
// Read temperature as Fahrenheit (isFahrenheit = true)
//temp = dht.readTemperature (true) ;

// Check if any reads failed and exit early (to try again) .
if (isnan (temp) || isnan (hum) ) {
Serial.println (F ("Failed to read from DHT sensor!") ) ;
return;
}

// Publish an MQTT message on topic esp32/dht/temperature
uint16_t packetIdPub1 = mqttClient.publish (MQTT_PUB_TEMP, 1, true, String (temp) .c_str () ) ;
Serial.printf ("Publishing on topic %s at QoS 1, packetId: %i", MQTT_PUB_TEMP, packetIdPub1) ;
Serial.printf ("Message: %.2f \n", temp) ;

// Publish an MQTT message on topic esp32/dht/humidity
uint16_t packetIdPub2 = mqttClient.publish (MQTT_PUB_HUM, 1, true, String (hum) .c_str () ) ;
Serial.printf ("Publishing on topic %s at QoS 1, packetId %i: ", MQTT_PUB_HUM, packetIdPub2) ;
Serial.printf ("Message: %.2f \n", hum) ;

// Publish an MQTT message on topic esp32/dht/temperature2
//uint16_t packetIdPub3 = mqttClient.publish (MQTT_PUB_TEMP, 1, true, String (temp) .c_str () ) ;
//Serial.printf ("Publishing on topic %s at QoS 1, packetId: %i", MQTT_PUB_TEMP, packetIdPub1) ;
//Serial.printf ("Message: %.2f \n", temp) ;

// Publish an MQTT message on topic esp32/dht/humidity2
//uint16_t packetIdPub4 = mqttClient.publish (MQTT_PUB_HUM, 1, true, String (hum) .c_str () ) ;
//Serial.printf ("Publishing on topic %s at QoS 1, packetId %i: ", MQTT_PUB_HUM, packetIdPub2) ;
//Serial.printf ("Message: %.2f \n", hum) ;

}
}